Kessler MOTION CONTROL: Oracle Controller Full (2.06.2 SL) Bedienungsanleitung Seite 29
- Seite / 43
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
REVOLUTION TIME LAPSE TIPS FOR ADVANCED MODE
MOTION CONTROL - ADVANCED
Here are some approximate gures to use as a starting point. These
gures where populated with a Canon 7D equipped with an extended
battery grip and a 15mm lens. Using these gures should get you close
to the reported results but you may need to adjust the MOTOR OFF
time to tweak the movement over time to perfect your results.
Being the load on the pan always remains the same, you will nd very
little variation once you have established the common result to your
unit. A few tips.
• Try to get your camera as close to perfect center of gravity that is
balanced up and down as well as forward to back.
• Leave your MOTOR ON time set to .05 SEC and your MOTOR POWER
set to 50.
• Make your distance over time adjustments by lengthening or
shortening the MOTOR OFF time.
PAN:
Keep MOTOR ON to .05 SEC, MOTOR POWER to 50 and run your
CYCLES to cover the time you want the time lapse to take (i.e. If you
want a 60 minute time lapse, adjust the CYCLES up to a number that the
ORACLE says will last 60 minutes).
TILT:
Keep MOTOR ON to .05 SEC, MOTOR POWER to 50 and
run your CYCLES to cover the time you want the time lapse
to take (i.e. If you want a 60 minute time lapse, adjust the
CYCLES up to a number that the ORACLE says will last 60 minutes).
These gures were populated with a camera set up that was
approximately 50% below center of gravity. If you were
to have the camera raised to be on perfect center of
gravity, you would use the same gures as the pan settings above.
Once you have tried one of these settings it is a good idea to write
down your result if it is dierent than what these charts state so you
can adjust or repeat the move next time. You may also tweak the
MOTOR POWER settings to ne tune results. For example if your
MOTOR POWER is 50 and you expect your move to go 90 degrees
over a period, and it actually goes 95 degrees you can reduce the
MOTOR POWER to say 45, so each movement is slightly slower. We do
not recommend setting the Motor Power over “50” when using long
exposures.
29
- TABLE OF CONTENTS 2
- CONNECTING THE ORACLE™ 4
- ORACLE™ OVERVIEW 5
- ORACLE OVERVIEWCONTINUED 6
- CAMERA CONTINUED 11
- CONTINUED 13
- MOTION CONTROL 16
- MOTION CONTROL - SMARTLAPSE™ 18
- SMARTLAPSE™ TIME LAPSE 19
- MOTION CONTROL - ADVANCED 20
- SLIDER/DOLLY 21
- HEAD UNIT 24
- STEPPER MOTORS DEMYSTIFIED 28
- MOTION CONTROL - SIMPLE 30
- CONFIGURING JOYSTICK 34
- UTILITY - BATTERY 36
- UTILITY - SIMPLE MODE POWER 37
- UTILITY - CURRENT SENSE 38
- TIME LAPSE HELP GUIDE 39
- 3 AXIS TIME LAPSE 40
- FLOW CHART 42
Verwandte Produkte und Handbücher für Zubehör für Video Kessler MOTION CONTROL: Oracle Controller Full (2.06.2 SL)
Zubehör für Video Kessler MOTION CONTROL: Controller Quick Start (3.02 SL) Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Zubehör für Video Kessler MOTION CONTROL: Oracle Controller Full (3.02 SL) Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Braun EN10 manuales
Manuales del propietario y guías del usuario para Herramientas Cosméticas Braun EN10.
Ofrecemos 1 manuales en pdf Braun EN10 para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern